¸ðµ¨
|
±¸¼º / ¼³¸í
|
»çÀ̹ö°ßÀû´ã±â
|
GT-1000A
|
2GHz to 20GHz, 10Watts
|
|
Warranty
|
1³â
|
Output Power
Output power is specified as minimum saturated power into 50 Ohm load with 0 dBm input. Input power for normal operation should be limited to +3 dBm maximum.
Range
|
Specification*
|
2 to 2.5GHz
|
+41.5 dBm (14 Watts) typical, +38.7 dBm (7.5 Watts) minimum
|
2.5 to 10GHz
|
+42 dBm (15 Watts) typical, +39.5 dBm (9 Watts) minimum
|
10 to 18GHz
|
+42 dBm (15 Watts) typical, +38.4 dBm (7 Watts) minimum
|
18 to 20GHz**
|
+42 dBm (15 Watts) typical, +38.4 dBm (7 Watts) minimum
|
* Note
: Output power with Option 01 is decreased by 1dB ** Note : Output power typical with Option 02 and Option 03 (Type-N output connector) Gain Flatness
Nominal gain is 40dB. Gain adjustment range is 10dB minimum. Gain flatness is specified as maximum variation with 0dBm input and 50 Ohm load.
Range
|
Specification
|
2 to 20GHz
|
+/- 2.5 dB maximum
|
2 to 6GHz
|
+/- 1.5 dB maximum
|
6 to 10GHz
|
+/- 1.5 dB maximum
|
10 to 18GHz
|
+/- 2.0 dB maximum
|
18 to 20GHz
|
+/- 2.0 dB maximum
|
Input and Output VSWR
Input : 50 Ohms, 2:1 max. Output : 50 Ohms, 2.3:1 max.
Additional Specifications
Parameter
|
Specification
|
Stability
|
Unconditionally Stable
|
Maximum Load VSWR
|
5:1
|
Harmonic Distortion*
|
< -30 dBc typical
|
Spurious*
|
< -60 dBc typical
|
Noise Figure
|
< 10 dB typical, < 14 dB maximum
|
Phase Linearity
|
20 degrees typical
|
* Note : Harmonics and spurious measured at -5dBm input power level
General Specifications
Line Voltage
|
85 to 264 VAC, 47 to 63 Hz, Single Phase
|
Line Power
|
300 VA maximum
|
Operating Temperature
|
0°C to +50°C
|
Storage Temperature
|
-20°C to +75°C
|
Cooling
|
Forced air, field replaceable fans
|
Phase Linearity
|
20 degrees typical
|
GT-1000A Rear Panel Connections
Connection
|
Description
|
RF Input
|
SMA (f) standard or Type-N (f) with Option 02
|
Coupler/Detector Output
|
SMA (f), -1 Volt DC nominal detector output at 10 Watts RF out, and nominally -250 mV at 1 Watt RF out, into high impedance.
|
AC Power Input
|
85 to 264 VAC, 47 to 63 Hz, Single Phase, 300 VA max.
|
Overview
The new Giga-tronics GT-1000A Microwave Power Amplifier offers linear high-power amplification across multioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
The GT-1000A rack mount broadband power amplifier, incorporating the latest CAP Wireless Spatium(TM) technology, delivers outstanding performance and exceptional value for electromagnetic interference / compatibility (EMI/EMC) test, semiconductor evaluation, load pull, antenna range and microwave laboratory applications. Excellence pulse performance and modulated signal fidelity makes these amplifiers ideal for defense EW and radar testing.
+40dBm Leveled Power from your Microwave Signal Generator
The GT-1000A Microwave Power Amplifier can be paired with the Giga-tronics 2420B or 2520A Frequency Synthesizer to deliver leveled output power up to +40 dBm from 2 to 20 GHz for CW or pulsed high power applications. The GT-1000A has an internal coupler / detector, which allows optimum leveling control directly from the synthesizer. Have all the power you need to overcome cable and switching losses or drive components like high power rated mixers and limiters.
Microwave Rack Mount Broadband Power Amplifier
Use the GT-1000A as a general-purpose R&D lab amplifier or as an exciter for power transmitters. Standard 19-inch rack mounts simplifies integration into your ATE systems for manufacturing test. The GT-1000A is ideal for EMI/EMC and standards lab testing where broadband frequency coverage saves time and money while improving test performance.
MeasurementXpress Interface
Replace traveling wave tube amplifiers with a high reliability, solid-state amplifier for improved noise performance and reduced IntermodulationDistortion (IMD). Test broadband devices from RF to microwave without changing transmission paths or exchanging amplifiers manually. Eliminate complex programming caused by manual switching of amplifiers during test. Do away with plugging and unplugging amplifiers in manual test stations by replacing your narrow band amplifiers with one broadband amplifier.
¸ðµ¨
|
±¸¼º / ¼³¸í
|
»çÀ̹ö°ßÀû´ã±â
|
Opt. 01
|
Add internal coupler/detector external ALC and power monitoring
|
|
Opt. 02
|
Type N(f) input and output connectors
|
No Charge
|
Opt. 03
|
SMA(f) input and Type N(f) output connectors
|
No Charge
|
Opt. 04
|
Both input and output connectors on front panel
|
No Charge
|
Opt. 46
|
Rack Slide Kit (HP Style Rack only)
|
|
|